The C1902 is an adjustable truck bed rack designed to create an elevated carrying area for larger cargo, including kayaks, luggage, cargo boxes and camping gear.

The C1372 is a clamp-on truck bed fishing rod holder designed to keep four or six rods organized, protected and easy to reach. It is not a truck bed rack.

Choose the C1902 if you need more space for large, long or bulky cargo above the truck bed.

Choose the C1372 if your main goal is to organize fishing rods without taking up unnecessary bed space. The two products serve different carrying needs and are sold separately.

The C1902 is available in different configurations:

• Full-size trucks without inner bed rails, including compatible F-150, Ram 1500, Silverado 1500 and Sierra 1500 models
• Tacoma and Gladiator models equipped with compatible inner bed rails

Select the configuration that matches your truck. If you are unsure, send us a clear photo of your bed rails and tonneau-cover setup before ordering.

The C1902 can work with compatible retractable tonneau covers equipped with T-slot rails. Compatibility depends on the cover design, rail position and available mounting clearance.

It may not work with every folding, soft roll-up or clamp-mounted cover. We recommend sending us a photo of your truck bed and cover rails for confirmation.

Yes. The C1902 offers adjustable length, width and height to accommodate different truck sizes and cargo setups.

Available height settings are approximately 18.8, 22.5 and 25 inches. Adjustment ranges vary between the full-size and mid-size configurations.

The C1902 is rated for up to:

• 300 lbs dynamic load while driving
• 600 lbs static load while the vehicle is parked
• 66 lbs on each side accessory panel

Always distribute weight evenly and account for the weight of mounting hardware and accessories. Never exceed the lowest load rating of the rack, truck bed, mounting system or attached cargo carrier.

The C1902 can support compatible rooftop tents within its published load limits. Before installation, verify the tent’s weight, mounting dimensions and hardware requirements.

The combined weight of the tent, occupants and accessories must remain within the applicable static and dynamic ratings.

The rack can be used for compatible:

• Kayaks and canoes
• Travel luggage and cargo boxes
• Camping equipment
• Rooftop tents
• Ladders and long materials
• Spare tires
• Light bars and outdoor accessories

Cargo carriers, platforms, tie-down straps and other accessories are not included unless specifically listed in the selected product package.

No. The C1902 includes the truck bed rack structure and the hardware specified in the package contents. A rooftop platform, cargo basket, rooftop tent and other cargo accessories are not included.

No. The C1902 uses a no-drill mounting system when installed on a compatible truck-bed configuration.

Installation method varies depending on whether the truck uses standard bed rails, inner rails or compatible T-slot tonneau-cover rails.

Most installations can be completed within approximately two hours. Actual installation time depends on your truck, bed-rail configuration and previous experience.

We recommend assembling the rack on a clean, level surface and checking every fastener again after the first trip.

The side rails provide additional tie-down and accessory-mounting points for compatible gear. They can help organize smaller equipment while keeping more of the truck-bed floor available.

Always confirm the weight and mounting requirements of any side-mounted accessory.

The C1372 uses 1.5-inch aluminum C-clamps and fits many standard pickup beds. However, it may not fit trucks with bed slides, certain tonneau covers, camper shells or other components that block the clamping area.

Check the available mounting space before ordering.

The C1372 is available in four-rod and six-rod configurations. Choose the version based on the number of rods you normally carry and the available space in your truck bed.

Yes. Its no-drill clamp system supports horizontal or vertical installation when sufficient mounting space is available.

The best orientation depends on your truck-bed layout, rod length and other cargo.

The holder uses shaped EVA foam to support the rods and reduce movement. Bungee retainers add another layer of security when traveling over uneven roads.

Always check that every rod is properly seated and secured before driving.

The aluminum C-clamps include rubber contact pads designed to reduce scratching at the mounting points. Clean the contact surfaces before installation and check the clamps periodically for proper tightness.

Installation typically takes about 10 minutes on a compatible truck bed. The clamp-on design does not require drilling or permanent modification.

The C1372 is primarily designed to clamp onto a compatible truck-bed edge or mounting surface. It is not listed as a dedicated C1902 rack attachment.

If you plan to use both products together, confirm that your truck provides enough mounting clearance and contact us with photos before ordering.

Only the parts listed in each product’s package contents are included. Luggage, kayaks, rooftop tents, cargo platforms, tie-down straps and other lifestyle accessories shown in application images may be sold separately.

Please confirm:

• Your truck’s year, make and model
• Full-size or mid-size bed configuration
• Inner bed-rail design
• Tonneau-cover type and rail shape
• Available clamp or T-slot mounting space
• Intended cargo and total weight

If you are still unsure, send us clear photos of both bed rails and your tonneau cover. Our team can help identify the most suitable setup.

TRUMGETA currently provides free U.S. shipping, a two-year warranty and a 30-day return period, subject to the terms listed on the website. Review the current shipping, warranty and return policies before placing your order.